Get a quote

Calculator

What size garage door motor do I need?

Enter the opening and the door. The calculator gives the door's rough weight, the class of motor to ask for, the rail or drum drive, and a price guide from published South African prices.

Garage door motor size calculatorA guide, not a design or a quote. Nothing you type here is sent anywhere.

01The opening

02The door

03What to ask for

    Door area
    -
    Weight, roughly
    -
    Motor class
    -
    Drive
    -
    Motor, supply only
    -
    Fitting, labour
    -

    A garage door motor does not lift the whole weight of the door. The springs do most of that, and the motor moves a door that is already balanced. That is why the door's size, material and daily use matter more than the number on the box: a heavy wooden double door that opens thirty times a day needs a stronger, cooler running motor than a light single steel door used twice a day.

    How the calculator works

    The door area is the width times the height. The rough weight is that area times a typical figure per square metre for the material: about 7 kg for aluminium, 10 kg for pre-painted steel, 13 kg for insulated panels and 17 kg for wood. The class follows from the weight, the width and the daily use: a standard home motor for most single and double doors, a heavy-duty home motor for heavy or very wide doors or busy ones, and an industrial motor for shutters, doors over about 16 m² or wider than 6 m.

    Sectional and tilt doors take a ceiling rail motor. The rail is about the door height plus 0.9 m, which leaves room for the trolley's travel and the motor head. Roll-up doors take a motor on the drum, and industrial shutters a drum or shaft motor, often three-phase with a chain for manual use.

    Check the door before the motor

    • Balance: with the motor released, a well balanced sectional door stays put about halfway up. If it drops or shoots up, the springs need adjusting first.
    • Headroom: a ceiling rail needs space between the top of the opening and the ceiling, and low garages may need a low headroom kit. Measure it and put it on your request.
    • Power: a plug point near the ceiling where the motor head goes saves a new circuit.
    • Rollers and tracks: worn rollers and bent tracks make any motor strain. See garage door rollers.

    What the price guide covers

    The motor range is a supply price for a domestic motor or kit of that door type, and the fitting range is labour only, both from South African retailer listings and cost guides checked in November 2026 (see each topic page). Kits differ: some include the rail, two remotes and a backup battery, others only the motor head. Extras such as an anti-theft bracket, safety beams, more remotes or a new plug point add to it. Industrial doors are quoted per job unless the door is a roller shutter of up to about 500 kg.

    Frequently asked questions

    Does a bigger motor make a heavy door safe?
    No. A motor that pulls harder hides a door that is out of balance, wears out sooner and can hurt someone if the force sensing is set high. Have the springs set so the door is balanced, then fit a motor of the right class.
    Is a double door always heavy-duty?
    Not always. A 4.9 x 2.1 m double door in aluminium weighs roughly 70 kg, which a standard motor handles if the door is balanced and opened a few times a day. The same door in pre-painted steel is roughly 100 kg, and wood, insulated panels or heavy use push it further, so the calculator then suggests heavy-duty.
    Can I use the same motor for a roll-up and a sectional door?
    No. Roll-up doors use a motor that drives the drum the door winds onto, while sectional and tilt doors use a ceiling rail with a trolley. Choose the motor for the door type first, then the strength.
    How accurate is the weight?
    It is a rough guide from typical weights per square metre. Panel thickness, glazing, wooden cladding and the struts on wide doors change it. The installer weighs up the actual door before choosing the motor.

    More garage door and gate tools

    Free quote request, no obligation

    Get quotes for the job

    Fill it in the way a fitter would size up the job: the door or gate, its size and what it is made of, how often it is used, or simply how many. The planner works out a rough weight and the motor to ask for, and draws it as you type. Installers and suppliers in your area quote you directly.

    Job cardGarage Door Motors
    Job
    59949
    Date
    2026-11-20
    Cost to you
    Free

    01The job

    02The door (optional, it helps the quote)

    Your door, front viewA guide

    -
    -
    -
    -
    -
    -
    Estimate
    -

    A guide from your figures, not a quote.

    03On site now

    04Your list (optional)

    1. 01
    2. 02
    Up to 12 lines: motors, remotes, batteries, springs, parts or work.
    Needs and options

    05Your details

    Free and no obligation. By sending you agree that we may share your request with suitable garage door and gate motor installers and suppliers. See our privacy policy.

    Get a free quote